1、塑膠材料的外觀相似，但可能會是不同的材料，客戶需試印確定其符合要求后，再批量印刷； 
2、在移印過程中，如出現拉絲或散開，可適當加入一些慢干膏即可; 
3、環境溫度過高，將會影響油墨原有質量； 
4、根據氣候變化，請遠離火源，陰暗環境下存放。
一,油墨使用技術參考 
印刷油墨是為是為了不具備烘烤條件而又不用外加固化劑而研制的單組份高性能油墨。油墨使用方便，不需加固化劑，不需烘烤，即可獲得優異的附著力。具有平光、附著力佳、耐沖壓、耐酒精等特點。 
1.適用范圍:鐵、鋁、合金、玻璃、陶瓷、電鍍、石材、陽極氧化鋁表面及烤（噴）漆面等 
2.稀釋劑:用本公司S-03稀釋劑 
3.固化劑:可添加TA-9154硬化劑10%增加附著力,提高墨膜硬度。 
4.膠刮硬度: 70-80度為宜，另外角度在60-70度為最佳。 
5.網目:適合于100-420網目印刷 
6.用量:用300目網版每公斤約可印30平方米. 
7.干燥方法: TA系列是屬于自然揮發干燥的油墨,墨層表干時間5-10分鐘：實干時間在24小時以內. 
48小時后達到最佳性能 1．或添加TA-9154硬化劑10%可增加附著力,提高墨膜硬度。2．烤箱90℃烘烤20分鐘佳能更優。 
二,測試方法（完全干燥后） 
1、劃百格后用3M膠紙剝離最少3次以上,無掉墨現象. 
2、用浸有純度99%的酒精的棉球，500G力在油墨表面來回擦拭200次無脫色。 
三、油墨使用注意事 
1．試印確認符合要求后再批量生產。 
2．做好被印物的表面清除油脂及雜質工作，以促進附著效果。 
3．需要套色時，應在前顏色表干或硬干后再進行套色工作。 
4．附著力、硬度、耐酸性、耐油性、耐去漬油性、抗劃傷性、耐磨性等性能的檢測，需要墨層完全固化后方可檢測。 
5．未經允許情況下，不得將本系列油墨與其它類型油墨混用及配色。 
6.添加固化劑后的使用時限：加入固化劑后的油墨使用時間為4~6小時，環境溫度越高使用時間越短，剩余油墨不可回收。
1, plastic material similar in appearance, but may be of different materials, customers need to try to determine its requirements, and then bulk printing;2, in the printing process, such as drawing or spread out, may be appropriate to add some slow dry plaster;In 3, the ambient temperature is too high, will influence the quality of the original ink;In 4, according to climate change, please stay away from fire, dark environment storage.One, the use of ink technology referencePrinting ink for is to do not have the baking condition without external curing agent and the development of one component high performance ink. The ink has the advantages of convenient use, without curing agent, without baking, can obtain excellent adhesion. Having a flat, adhesive force is good, punching resistance, alcohol resistance characteristics.1 scope of application: iron, aluminum, alloy, glass, ceramic, plating, stone, anodized aluminum surface and baked ( spray paint etc. )2: with the company S-03 diluent diluent3: add TA-9154 curing agent hardening agent 10% increased adhesion, improve the ink film hardness.The 4 squeegee hardness: 70-80 degrees appropriate, the other point of view in the 60-70 degrees is the best.5: suitable for 100-420 screen printing mesh6: amount with 300 mesh screen every kilograms about Printing 30 square meters.The 7 drying methods: TA series belongs to natural volatile drying inks, ink layer surface dry time drying time: 5-10 minutes in 24 hours.After 48 hours to achieve the best performance of 1 or add TA-9154 hardening agent 10% can increase the adhesion, improve the ink film hardness. 2 90℃oven and bake for 20 minutes and canon.Two, test method for ( completely dry )1, row grid with 3M after tape stripping at least 3 times above, no drop ink phenomenon.In 2, impregnated with a purity of 99% alcohol tampon, 500G force on the surface of the printing ink rub 200 times without decolorization.Three, the use of ink.1 print test confirmation after the mass production.2 be printed material surface to remove grease and impurity, to promote the attachment effect.3 need to register, should be in the first color table stem or stem and then register work.The 4 adhesion, hardness, acid resistance, oil resistance, resistance to stains oily, scratch resistance, abrasion resistance and other performance test, need ink layer is completely cured before detection.5 without permission, may not use the series of ink and other types of ink mixing and matching.6 adding curing agent after the use of time: the curing agent is added after the ink using time for 4~6 hours, the higher ambient temperature using the shorter the time, the remaining ink unrecyclable.[本信息來自于今日推薦網]